Thermal Insulation Panel Adhesive Mortar

• Click to open image! Click to open image!
•  

The Name of the Product     : OPTIMUM THERM

Product Group               : Thermal Insulation Panel Adhesive Mortar

Description                     : Cement-based, reinforced with chemical additives, polymer and fibers, developed

                                        for internal and external coating of thermal insulation panels, practical and easy-to-

                                        use adhesive mortar.

Packaging Type             : In 25 kg craft bags

Color                               : Gray

Standard                         : TSE K 112 April 2011

Areas of Use                   : Used for affixing sound and thermal insulation panels such as XPS, EPS, rock wool

     to mineral based surfaces on outdoor and indoor areas.

Characteristics/Advantages : Durable and long-lived.

                                    Highly durable.  

                                    Resistant to water, frost, moisture and heavy weather conditions.

                                    Minimizes the risk of cracking.

                                    High water permeability.

                                    Easy preparation and application.

                                    Non-flammable.

Technical Specifications:

Color                                                                     : Gray

Adhesive Strength (On Mineral Surfaces)      : ≥ 0,5 N/mm²

Adhesive Strength (On EPS)                             : ≥ 0,08 N/mm²

Compressive Strength                                         : > 6 N/mm²

Flexural Strength                                                : > 2 N/mm²

- These figures are provided for temperatures between +23±2 ºC and for 50±5% relative humidity.

Application Information :

Application Temperature                                    : (+5°C) - (+35°C)

Crustation Period                                                : 25 minutes

Settling Time                                                       : 10 minutes

Mixing ratio                                                         : 6 - 7 lt water / 25 kg powder

Plugging Starting Time                                       : 24 hours after application

Surface Preparation            :

The surfaces shall be clear of substances that may prevent adherence such as surface molding grease, dust, dirt, paint, detergent, etc. All imperfections on the surface shall be repaired with Parexgroup repair plaster before the product is applied or should be undercoated with Geseras EM2. Further, the thermal insulation panel should be dry and clean before affixing.

Application                :

• Slowly pour 25 kg’s of Optimum Thermal Insulation Panel Plaster to the mixing container and mix with a slow-speed mixer until a homogenous and pellet-free mixture is obtained. Wait for 10 minutes for settling, and then mix for another 1-2 minutes then apply.
• The adhesive mortar should be applied to the circumference of the thermal insulation panel with a trowel 4-5 cm wide and 1 cm thick. Apply to the middle parts of the panel point to point. If the panel is made out of stone wool, after the application, the adhesive mortar should be scrapped off and then the rock wool panel should be undercoated by rubbing the product on the panel again with the help of a trowel.
• Do not apply the adhesive mortar to the corners and sides of the panels.
• The prepared panels shall be arranged by touching each other by placing the panel to the sub-basement profile with a little pressure to the surface and from bottom up.
• Affixing shall be carried out with the help of a jig and by tightly pressing the panel to the surface in order to form a smooth surface.
• The application shall not be carried out under direct sunlight, rain and during heavy winds.
• The prepared mortar shall be used within maximum 3 hour’s time.

Consumption             :   4-5 kg/m²

Storage Life:

The expiry date is 8 months from the date of production provided that it is stored in sealed (unopened) original package and not subject to direct sunlight, humidity and frost and with maximum 8 times piling.

Safety Precautions / Warnings:

• Use between +5 Cº and +35 Cº.
• No foreign substance may be added to the prepared mortar.
• The expired mortar should not be re-used by mixing with water or dry mortar.
• Do not apply under direct sunlight.
• Do not apply on surfaces subject to sunlight for prolonged periods or that are very hot or frozen.
• Wait 24 hours for plugging.
• Absorbent surfaces should be wetted before the application or should be undercoated with a suitable undercoat.
• Do not inhale the dust of the product since the material is cement based; avoid contact with the skin and eyes.
• View Product Safety Data Sheet for more information about health and safety titles.

Hazard Warnings:

R 36/38     : Irritating to eyes and skin.

Safety Warnings       :

S 2             : Keep out of the reach of children.

S 28           : Wash with plenty of water in case of contact with the skin.

S 36/37/39 : Use protective clothing, gloves, goggles/mask while working with the product.

Xi : Irritant

Please click here for pdf document