Heat Insulating Panel Adhesive Mortar

• Click to open image! Click to open image!
•  

The Name of the Product     : GESTERM 410

Product Group               : Heat Insulating Panel Adhesive Mortar

Description                     : Cement-based, chemical additive and polymer reinforced, practical and easy-to-use

                                        adhesive mortar used for affixing of all heat insulation panels to mineral based

                                        surfaces externally and internally

Packaging Type             : In 25 kg craft bags

Color                               : Gray

Standard                         : TSE K 112 April 2011

Areas of Use                   : For affixing of heat and acoustic insulation panels such as XPS, EPS, stone wool,

     etc. to mineral based surfaces on internal and external facades.

Characteristics/Advantages:

Durable and long-lived.

                                    Highly durable.

                                    Resistant to water, frost, moisture and heavy weather conditions.

                                    High water permeability.

                                    Easily prepared and applied.

                                    Non-flammable.

Technical Specifications   :

Color                                                                     : Gray

Adhesive Strength (On mineral surfaces)         : ≥ 0,5 N/mm²

Adhesive Strength (On EPS)                              : ≥ 0,08 N/mm²

Compressive Strength                                         : > 10 N/mm²

Flexural Strength                                                : > 4 N/mm²

* Without requiring the samples to be tested, in accordance with decision no. 2000/605/EC.

- These figures are provided for temperatures between +23±2 ºC and for 50±5% relative humidity.

Application Information :

Application Temperature                                    : (+5°C) - (+35°C)

Crustation Period                                                : 20 minutes

Settling Period                                                     : 10 minutes

Mixing Ratio                                                        : 5-6 lt water / 25 kg powder

Plugging Starting Period                                     : 24 hours after application

Surface Preparation    :

The surfaces shall be clear of substances that may prevent adherence such as surface molding grease, dust, dirt, paint, detergent, etc. All imperfections on the surface shall be repaired with Parexgroup repair plaster before the product is applied. Highly absorbent surfaces should be dampened or undercoated with Geseras EM2. Further, the heat insulation panels should be dry and clean.

Application    :

• Slowly add Gesterm 410 heat insulation panel adhesive mortar to 5-6 liters of water in the mixing container slowly and mix with a slow-speed mixer until a homogenous and pellet-free mixture is obtained. Wait for 10 minutes for settling, and then mix for another 1-2 minutes then apply.
• The adhesive mortar should be applied around the heat insulation panel with a width of 4-5 cm and thickness of 1 cm with the help of a trowel. In the middle area, just rub the mortar at certain points. If the panel is made of stone wool, after this first procedure, the material should be scrapped off from the adhesive surface and undercoating application should be carried out by re-applying the material to the panel again with the help of a trowel.
• Mortar should not be applied to the sides and to lateral surfaces of the panels.
• The prepared panels shall be arranged by touching each other by placing the panel to the sub-basement profile with a little pressure to the surface and from bottom up.
• Affixing shall be carried out with the help of a jig and by tightly pressing the panel to the surface in order to form a smooth surface.
• The application shall not be carried out under direct sunlight, rain and during heavy winds.
• The prepared mortar shall be used within maximum 3 hour’s time.

Consumption             :   4-5 kg/m²

Storage Life   :

The expiry date is 8 months from the date of production provided that it is stored in sealed (unopened) original package and not subject to direct sunlight, humidity and frost and with maximum 8 times piling.

Safety Precautions/Warnings:

• Use between +5 Cº and +35 Cº.
• No foreign substance may be added to the prepared mortar.
• The expired mortar should not be re-used by mixing with water or dry mortar.
• Do not apply under direct sunlight.
• Do not apply on surfaces subject to sunlight for prolonged periods or that are very hot or frozen.
• Wait for 24 hours before plugging.
• Before the application, highly absorbent surfaces should be wetted or undercoated with a suitable undercoat.
• Do not inhale the dust of the product since the material is cement based; avoid contact with the skin and eyes.
• View Product Safety Data Sheet for more information about health and safety titles.

Hazard Warnings:

R 36/38     : Irritating to eyes and skin.

Safety Warnings       :

S 2             : Keep out of the reach of children.

S 28           : Wash with plenty of water in case of contact with the skin.

S 36/37/39 : Use protective clothing, gloves, goggles/mask while working with the product.

Xi : Irritant

Please click here for pdf document