Flex pool ceramic adhesive mortar
https://geserparex.dumanli.net/en/tile-adhesives/geserpool-120#sigProGalleria6d58d19b66
The Name of the Product : GESERPOOL 120
Product Group : Flex pool ceramic adhesive mortar
Description : Cement-based adhesive mortar with high adherence strength and high stability,
reinforced with chemical additives, polymers and mineral fillings and manufactured
in accordance with TS EN 12004, C2T class, used for affixing granite, ceramic, tiles,
marble, bête be, floor tiles, etc. to walls and floors exposed to water pressure.
Packaging Type : In 25 kg craft bags
Color : Gray and white
Standard : TS EN 12004 – Class: C2T.
Areas of use : For affixing of , ceramic, tiles, marble, bête be, floor tiles, etc. to internal and
external facades, walls and floors in swimming pools, water tanks and wet areas,
terrace and roof ceramic coatings.
Characteristics/Advantages :
Durable and long-lived. Does not vertically slide and has high adherence strength.
Durable against water and moisture.
Easy preparation and application.
Suitable solution for surfaces in contact with water.
Non-flammable.
Technical Specifications:
Color : Gray and White
Initial Adhesive Strength : > 1 N/mm2
Adhesive Strength after water immersion : > 1 N/mm2
Adhesive Strength after hot ageing : > 1 N/mm2
Adhesive Strength after freezing-thawing cycles : > 1 N/mm2
Opentime adhesive strength (min. After 20 minutes) : >0,5 N/ mm2
Sliding : < 0,5 mm
Temperature Endurance : -30ºC and +60ºC
Fire Reaction : *European Type A1
* Without requiring the samples to be tested, in accordance with resolution no. 2000/605/EC
- These figures are provided for temperatures between +23±2 ºC and for 50±5% relative humidity.
Application Information:
Application Temperature : (+5°C) - (+35°C)
Operation Period : 25 minutes
Settling Period : 5 minutes
Mixing Ratio : 5 - 6 lt water / 25 kg powder
Pot Life : Max. 3 hours
Ready for use period : 24 hours after application (this period shall be longer in lower temperatures and shorter in higher temperatures)
Jointing Application Start-up Time : 24 hours for walls – 48 hours for floors
Surface Preparation :
The surfaces shall be clear of substances that may prevent adherence such as surface molding grease, dust, dirt, paint, detergent, etc. All imperfections on the surface shall be repaired with Parexgroup repair plaster before the product is applied. Highly absorbent surfaces should be dampened or undercoated with Geseras EM2.
Application :
- Slowly add Geserpool 120 to 6-7 liters of water in the mixing container slowly and mix with a slow-speed mixer until a homogenous and pellet-free mixture is obtained. Wait for 5 minutes for settling, and then mix for another 1-2 minutes then apply.
- The adhesive mortar should be used by applying pressure to the surface and then should be chiseled with a steel-toothed trowel selected according to the material to be affixed to the surface.
- The affixing process should be carried within 20 minutes after the chiseling has taken place. If this period has elapsed for some reason, the adhesive mortar should be scraped off from the surface.
- For good adherence, the air bubbles shall be removed with the help of a rubber hammer.
- If film has formed during the application, that area should be re-chiseled and no application shall be carried out on very hot or frozen surfaces.
- Mortar should be rubbed on both the ceramic tile and the surface for tiles larger than 20x20 cm for wall and floor applications.
- The prepared mortar should be consumed within maximum 3 hours.
Consumption
Tile Dimensions Tooth Measurements Consumption
10x10 and 20x20 cm 8x8x8 mm One-sided affixing 5 kg/m²
20x20 and 60x60 cm 10x10x10 mm Double-sided affixing 7-8 kg/m²
Storage Life:
The expiry date is 8 months from the date of production provided that it is stored in sealed (unopened) original package and not subject to direct sunlight, humidity and frost and with maximum 8 times piling.
Safety Precautions/Warnings:
- Use between +5 Cº and +35 Cº.
- No foreign substance may be added to the prepared mortar.
- The expired mortar should not be re-used by mixing with water or dry mortar.
- Do not apply on surfaces subject to sunlight for prolonged periods or that are very hot or frozen.
- Wait for 24 hours for jointing on walls and for 48 hours for floors.
- Before the application, highly absorbent surfaces should be wetted or undercoated with a suitable undercoat.
- Do not inhale the dust of the product since the material is cement based; avoid contact with the skin and eyes.
- View Product Safety Data Sheet for more information about health and safety titles.
Hazard Warnings:
R 36/38 : Irritating to eyes and skin.
Safety Warnings :
S 2 : Keep out of the reach of children.
S 28 : Wash with plenty of water in case of contact with the skin.
S 36/37/39 : Use protective clothing, gloves, goggles/mask while working with the product.
Xi : Irritant
